High performance in a lightweight, compact projector featuring a variety of functions for bright, vivid images. Ultra Portable, High Brightness Projector features DLP ™ technology Lightweight at 2.0 kg Auto Focus Function Direct Power Off Function Wall Colour Correction Auto Vertical keystone Correction Streamlined cabinet in a pearl-white finish   High brightness of up to 3000 ANSI lumens with a compact, lightweight, 2.0 kg body Although it has a highly transportable lightweight body weighing 2.0 kg, it achieves high brightness of 3000 ANSI lm, which is sufficient for use in a bright room. (This is for the LT35. The brightness is 2600 ANSI lm and 2200 ANSI lm for the LT30 and LT25, respectively.) Auto Focus Function by the focus sensor The focus of the projected image is adjusted automatically by measuring the distance between the focus sensor and the screen. This function activates immediately whenever the power is turned on, the zoom function is adjusted or the position of the main unit is changed, so the projector can be set up easily without focusing every time. The projector can be put away quickly with Direct Power Off function The projector can be turned off , even when projecting an image, using a power strip equipped with a switch and a breaker. Also, the power cable can be removed immediately after turning off the projector, so that the user can put the projector away immediately after terminating a conference or class. Wall Colour Correction enables vivid images even without a screen Without a screen, the projected images may be affected by the colours of the wall or blackboard. This projector has built-in colour correction for projecting images on a coloured wall or blackboard, so that the colour tones of the projected images can be approximated to those projected on a white screen. The following eight colour options are available as user selections: blackboard, blackboard (gray), light yellow, light green, light blue, sky blue, light rose and pink. Auto Vertical Keystone Correction adjusts the trapezoidal distortion to correct the projected image If the position of the screen is too high or low, the projector must be installed at an angle, resulting in trapezoidal distortion of the projected images. The acceleration sensor built into the main unit senses the inclination of the unit in the vertical direction and then corrects for any trapezoidal distortion in the projected images automatically to project square images. (+/- 16 degrees from the projection angle) The user can set up the projector very quickly and easily since it is not necessary to correct it manually. Reproduction of more vivid colours are now available by the introduction of a newly designed Colour Wheel Newly designed Colour Wheel reproduces images in more vivid colours. With the White Peaking function, more natural, vivid images can be projected. Furthermore, the user can correct gamma and adjust colour temperature with detailed settings. Eco Mode can be set with the remote controll In the Eco Mode, the lamp replacement period can be extended up to a maximum of 2500 hours (estimated). (The lamp replacement period in Normal Mode is 2000 hours (estimated). By selecting this mode, total cost of ownership can be reduced effectively. Since it can be switched to Eco Mode with the remote controll as well, the user can easily change the lamp mode quickly. Security function prevents unauthorized use or theft By using passwords, the projector cannot be used by unauthorized persons. Once the Security function is in effect, a message requesting the password is displayed when the power of the main unit is turned on. It is impossible to project an image unless the proper password is entered. Streamlined body in a new pearl-white finish The sleek, rounded design and pearl-white finish compliments any environment and decor. Terminal Panel.     Specifications Model Name LT35 LT30 LT25 DMD Panel*1 1chip DMD reflection type, 0.7 inch 1,024 x 768 pixels, Aspect Ratio 4 : 3 Lens Manual Zoom (Renge 1 to 1.2) (f=25.7mm to 30.8mm) Auto Focus (effective range: 1.4m to 5.5m*2)/Power focus Lamp Normal Mode 220W AC 200W AC Lamp Eco Mode 170W Lamp Life*3 Normal Mode 2,000H Eco Mode 2,500H Power Consumption Normal Mode 280W 260W Eco Mode 230W 230W Standby Mode 8W 8W Input Current 3.1A to 1.4A (100 to 240V AC) 2.8A to 1.3A (100 to 240V AC) Light Output Normal Mode 3,000 ANSI lumens 2,600 ANSI lumens 2,200 ANSI lumens Lamp Eco Mode 2,300 ANSI lumens 2,200 ANSI lumens 1,900 ANSI lumens Contrast Ratio (White/Black) 1,600 : 1 1,500 : 1 Quietness Normal Mode 40dB 37dB Eco Mode 33dB 33dB Image Size 30 inch to 300 inch diagonal Projection Distance 1.1m to 13.3m Projection Angle 10°to 12° Maximum Resolution SXGA+ (1,400 x 1,050) With scaling technology Synchronization Range Horizontal 15kHz to 100kHz (RGB:24kHz or over) Vertical 50Hz to 85Hz Video Bandwidth RGB: 100MHz Input Terminals 1 Computer Input D-Sub Mini 15pin RGBHV VGA, SVGA, XGA, SXGA, SXGA+ RGB 0.7Vp-p/75Ω H/V Sync 4.0Vp-p/TTL Polarity Composite Sync 4.0Vp-p/TTL Level Sync on G 0.3Vp-p/75Ω Negative Polarity Stereo Mini Jack Stereo L/R 0.5Vrms/22kΩ or over 1 Component Input (Sharing With Computer) D-Sub Mini 15pin (Sharing With Computer Input) Y 1.0Vp-p/75Ω (With Sync) Cb · Cr ( Pb · Pr) 0.7Vp-p/75Ω Compatible signals 1125i(1080i), 750p(720p), 525p(480p), 525i(480i)/60Hz 1125i(1080i), 625p(576p), 625i(576i)/50Hz, Progressive PAL-scan/50Hz DVD Component Video Signal (15kHz) Audio Input is Sharing With Computer Same With Computer 1 Video Input RCA pin Composite Video NTSC/NTSC4.43/PAL/PAL-N/PAL-M/PAL-60/SECAM 1.0Vp-p/75Ω Audio Input is Sharing With Computer Same With Computer 1 S-Video Input Mini DIN-4pin Y 1.0Vp-p/75Ω C 0.286Vp-p/75Ω Audio Input is Sharing With Computer Same With Computer Control terminals PC Control Mini DIN-8pin RS-232C Built-In Speaker 1W Monaural Keystone Correction Vertical Automatic/Manual max±16° Environment Operational Temperatures 5°C to 40°C, 20 to 80% Humidity (Non-Condensing) (Eco mode selected automatically at 35°C to 40°C) Storage Temperatures -10°C to 50°C, 20 to 80% Humidity (Non-Condensing) Power Requirement 100 to 240V AC, 50Hz/60Hz Regulations For United States UL Approved (UL 60950-1), Meets FCC Class B Requirements For Canada UL Approved (CSA 60950-1), Meets DOC Canada Class B Requirements For Australia/New Zealand Meets AS/NZS CISPR.22 Class B For Europe Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3), Meets Low Voltage Directive (EN60950-1, TUV GS Approved) Net Weight 2.0kg Dimensions (WxHxD) 260mm x 89mm x 208.5mm (Not Including Protrusions) *1 : DMD Panel technology consists of fine picture cells with more than 99.99% of the cells being active. *2 : Sizes of the projected images shall be 32 inches when the throwing distance is 1.4m, while it shall be 149 inches when the throwing distance is 5.5m. When the throwing distance is beyond 5.5m, it means that the focus sensor will not work correctly and that you need to use the FOCUS button to adjust the focus manually. In some cases, the Auto Focus may not work correctly or the Auto Focus range can be made narrower, depending on the environmental conditions. *3 : Lamp life is defined as the average time span for the brightness of the lamp to be reduced by half, it dose not refer to the warranty period for the lamp. All specifications are subject to change without notice.   Soft Case (basic accessory) Options Replacement lamp LT35LP (For LT35) LT30LP (For LT30/25)   Model codes, specifications and available options may differ by region. For detailed information, please contact the NEC sales company or dealer in your area. All brand and product names are registered trademarks of their respective holders. Further trademark information